Abstract

Technology is currently developing more than advanced, however, wear factor in the valves moving parts remain as a problem. In this paper, selection of the right materials for improved liner motion gate valves' hermetic elements is studied based on the friction correlation method. Research is carried out in wear & tear machine for different grades of steels. A comparative analysis is done among the generated results. The hardness of new valve hermetic elements, materials was selected according to Brinell (GOST 4543). Steel 20X for the first saddle, 38X2MYA alloy steel for main gate and steel 40X was selected for the second saddle. It was found that the following condition must be met among the steel structures used to construct the packing element of the valve. 〖HB〗_x1<〖HB〗_x2>〖HB〗_x3 This paper reviews the existing models used for investigating the friction and weariness in the parts of valves. Some of other methods such as finite element simulation tools were also reviewed. The main aim of this paper is to find nearly ideal material grade that can realistically be used in construction of valve elements. A comparative analysis, which includes the approaches and limitations on the related works was presented. By the end of this paper, a conclusion is drawn and suggestions aspects for future research were stated.

Keyword

Straight gate valve, Friction, Efficiency, Reliability, Longevity, Packing element, Gate, Saddle, Hermetic elements.

Cite this article

Aslanov JN, Mammadov KS, Zeynalov NA

Refference

[1][1]Aslanov JN, Abasova SM, Huseynli ZS. The management of characteristics of the new two-layer rubber matrix seals. EUREKA: Physics and Engineering. 2020; 5:60-8.

[2][2]Albaina I, Arregui FJ, Bidaguren-alday C, Bidaguren I. Influence of butterfly and gate valves upstream large water meters. Water. 2020; 12(9):1-24.

[3][3]Zic E, Banko P, Lesnik L. Hydraulic analysis of gate valve using computational fluid dynamics (CFD). Scientific Review Engineering and Environmental Sciences. 2020; 29(3):275-88.

[4][4]Capodaglio EM. Comparison between the CR10 Borgs scale and the VAS (visual analogue scale) during an arm-cranking exercise. Journal of Occupational Rehabilitation. 2001; 11(2):69-74.

[5][5]Lin Z, Sun X, Yu T, Zhang Y, Li Y, Zhu Z. Gas–solid two-phase flow and erosion calculation of gate valve based on the CFD-DEM model. Powder Technology. 2020; 366:395-407.

[6][6]Michalska-Pozoga I, Jakubowski M. CFD analysis of the flow of a polymeric material inside the double-cone plasticization-homogenization zone of the screw-disc extruder. Przemysl Chemiczny. 2015; 94(12):2105-11.

[7][7]Vahidov MA, Karimov OM, Eyvazova ZE. Oil and Gas equipment, 2008.

[8][8]Titenko A, Demchenko L, Kozlova L, Babanli M, Ren TZ, Titenko Y. Deformational behavior of Cu–Al–Mn alloys under the influence of temperature and mechanical stress. Applied Nanoscience. 2020; 10(8):3097-101.

[9][9]Lin Z, Ma G, Cui B, Li Y, Zhu Z, Tong N. Influence of flashboard location on flow resistance properties and internal features of gate valve under the variable condition. Journal of Natural Gas Science and Engineering. 2016; 33:108-17.

[10][10]Mamedov VT, Mamedov GA, Aslanov JN. Stress-strain state of sealing rubber membranes at large deformations. Journal of Applied Mechanics and Technical Physics. 2020; 61(2):286-91.

[11][11]Harp SR, Salant RF. Inter-asperity cavitation and global cavitation in seals: an average flow analysis. Tribology International. 2002; 35(2):113-21.

[12][12]Babanlı MB, Mamedov GA, Mammadov VT, Aslanov JN. İmpact of thermoelastık deformatıon on work of rotatıng preventers sealıng. In science and education: materıals of the xıı international research and practice conference. 2016.

[13][13]Srivastava S, Shet K, Kulkarni S. A comparative study of two methodologies for nonlinear finite element analysis of knife edge gate valve sleeve. International Journal of Mechanical Engineering and Technology. 2015; 6(12):81-90.

[14][14]Kyzy SAB, Nuraddin AJ, Kyzy HZS. Diagnostics of high pressure oil equipment. International scientific and practical conference 2021 (pp. 65-9).

[15][15]https://digitalcommons.usu.edu/cgi/viewcontent.cgi?referer=&httpsredir=1&article=2454&context=etd. Accessed 20 November 2021.

[16][16]Aslanov CN, Mammadov KH. İncreasing improved plug valve’s efficiency. Science, Technology and Higher Education. 2015.

[17][17]He X, Zhang C, Tian D. Strength analysis and structure optimization of gate valve body based on finite element software. In E3S web of conferences 2019 (pp. 1-6). EDP Sciences.

[18][18]Nuraddin AJ, Baxman SA, Abulfas HI. Model design for predicting the efficiency of improved valve constructions during statistical data based exploitation. IFAC-PapersOnLine. 2019; 52(25):547-50.

[19][19]Ibrahim H , Camaladdin H. Simulation of kinetic curves of thermo-oxidative destruction of prolimers using differential equations of fractional order. ETM - Equipment, Technologies, Materials. 2021:52-62.

[20][20]Chen T, Ji J, Fu Y, Tian P, Zhou J, Yang X. Tribological analysis of picosecond laser partially textured thrust bearings with circular grooves machined: theory and experiment. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. 2022; 236(1):105-22.

[21][21]US Department of Energy. DOE fundamentals handbook: mechanical science.2016.

[22][22]Magazine of Toficgo, uploads 04/VG_RU-nouvelle-adresse, 2015.

[23][23]Addy AL, Morris MJ, Dutton JC. An investigation of compressible flow characteristics of butterfly valves. Journal of Fluids Engineering, Transactions of the ASME.1985; 107(4):512-7.

[24][24]Eom K. Performance of butterfly valves as a flow controller. Journal of Fluids Engineering. 1988; 110(1): 16-19.

[25][25]Kimura T, Tanaka T, Fujimoto K, Ogawa K. Hydrodynamic characteristics of a butterfly valve-prediction of pressure loss characteristics. ISA Transactions. 1995; 34(4):319-26.

[26][26]Lin F, Schohl GA. CFD prediction and validation of butterfly valve hydrodynamic forces. In critical transitions in water and environmental resources management 2004 (pp. 1-8).

[27][27]Song X, Wang L, Park Y. Fluid and structural analysis of large butterfly valve. In AIP conference proceedings 2008 (pp. 311-4). American Institute of Physics.

[28][28]Guan Song X, Park YC. Numerical analysis of butterfly valve-prediction of flow coefficient and hydrodynamic torque coefficient. In proceedings of the world congress on engineering and computer science 2007(pp. 24-6).

[29][29]Chaiworapuek W, Champagne JY, El HEM, Kittichaikan C. An investigation of the water flow past the butterfly valve. In AIP conference proceedings 2010 (pp. 249-62). American Institute of Physics.

[30][30]https://www.plm.automation.siemens.com/global/en/products/simcenter/STAR-CCM.html. Accessed 23 November 2021.

[31][31]Butterfly valves-torque, head loss, and cavitation analysis: M49. American Water Works Association; 2001.

[32][32]Yunus A, Çengel, Cimbala JM. Fluid mechanics: fundamentals and applications. McGraw-Hill Higher Education; 2010.

[33][33]Coleman HW, Steele WG. Experimentation, validation, and uncertainty analysis for engineers. John Wiley & Sons; 2018.

[34][34]Munson BR, Okiishi TH, Huebsch WW, Rothmayer AP. Fluid mechanics. Singapore: Wiley; 2013.

[35][35]Patil PB, Gambhire VR. Structural analysis of gate valve body using FEA. International Journal of Engineering Research & Technology. 2014; 3(6):1815-8.

[36][36]Jatkar KH, Dhanwe SS. Finite element analysis of gate valve. International Journal of Engineering and Innovative Technology. 2013; 2:277-81.

[37][37]Pujari AA, Joshi GS. Analysis and design optimization of 8’’-600# gate valve body using FEA and stress analysis. International Journal of Research in Engineering and Technology. 2016; 4(2):440-3.

[38][38]Mantati S, Surde AN. Finite element analysis of flexible wedge type (2”#150) gate valve. International Journal of Emerging Technology and Advanced Engineering. 2015; 5(6):194-8.

[39][39]Sathishkumar S, Kannan M, Amirthalingam P, Arunkumar S, Natesh NS. Material development for thermo mechanical strained structural application. International Journal of Mechanical Engineering and Technology. 2016; 7(6):236-44.

[40][40]https://webstore.ansi.org/preview-pages/MSS/preview_MSS+SP-91-2009.pdf. Accessed 23 November 2021.

[41][41]Jackson AS, Osburn HG, Laughery KR, Vaubel KP. Validity of isometric strength tests for predicting the capacity to crack, open, and close industrial valves. In proceedings of the human factors society annual meeting 1992 (pp. 688-91). Sage CA: Los Angeles, CA: SAGE Publications.

[42][42]Beckerle P, Schaede H, Rinderknecht S. Fault diagnosis and state detection in centrifugal pumps-a review of applications. In proceedings of the 9th IFToMM international conference on rotor dynamics 2015 (pp. 387-98). Springer, Cham.

[43][43]Chen Z, Liu T, Li J. The effect of the O-ring on the end face deformation of mechanical seals based on numerical simulation. Tribology International. 2016; 97:278-87.

[44][44]Xie F, Li Y, Ma Y, Xia S, Ren J. Cooling behaviors of a novel flow channel in mechanical seals of extreme high-speed rotation for cryogenic rockets. Cryogenics. 2020.

[45][45]Wang X, Liu M, Kao-walter S, Hu X. Numerical evaluation of rotordynamic coefficients for compliant foil gas seal. Applied Sciences. 2020; 10(11):1-9.

[46][46]Mosavat M, Moradi R, Takami MR, Gerdroodbary MB, Ganji DD. Heat transfer study of mechanical face seal and fin by analytical method. Engineering Science and Technology, an International Journal. 2018; 21(3):380-8.